Repairing a Chainsaw and Other Happenings / Ремонт Цепной Пилы и Другие События

in #life3 years ago

DSC_0001.JPG

English
Русский

This is a battery-powered chainsaw that I recently took apart. I was mildly annoyed to discover that I had to disassemble the entire machine in order to reach the gearbox.
Это цепная пила на батарейках, которую я недавно разобрал. Я был слегка раздосадован, обнаружив, что мне пришлось разобрать всю машину, чтобы добраться до коробки передач.

DSC_0002.JPG

The gearbox attached to the electric motor - yes, this tiny thing is all there truly is to this chainsaw. Mostly, this "tool" is a cheap plastic toy... a toy that can cause serious injury, but a toy nonetheless. After all, I broke it.
Коробка передач, соединенная с электродвигателем - да, эта крошечная штука - все, что действительно есть в этой цепной пиле. В основном этот "инструмент" - дешевая пластиковая игрушка... игрушка, которая может нанести серьёзную травму, но тем не менее игрушка, в конце концов, я её сломал.

DSC_0006.JPG

See the problem?
Видите проблему?

DSC_0007.JPG

This gear has only 32 teeth, it should have 36. I will build up the broken teeth with welding filler, and then mill them down again. In order to do so, I will need a gear-tooth cutter.
У этой шестерни (зубчатка?) всего 32 зуба, у неё должно быть 36. Я восстановлю сломанные зубы сварочным наполнителем, а затем снова их фрезеруют. Для этого мне потребуется зуборезную фрезу.

gear cutter indicated.jpg

This is a gear-tooth cutter, but it's the wrong size. The box directly above it has another gear-tooth cutter in it, but also the wrong size. Luckily, I have a set of gauges for determining which size I need:
Это зуборезная фреза, но она не того размера. В коробке прямо над ней есть ещё одна зубчатая фреза, но тоже не того размера. К счастью, у меня есть набор мер для определения того, какой размер мне нужен:

DSC_0003.JPG

After that, most of the work will involve this contraption:
После этого большая часть работы будет выполнена с помощью этого станка:

DSC_0009.JPG

Still, this will have to wait, because hunting season is not yet over, so I have to deal with this:
Однако с этим придется подождать, потому что сезон охоты ещё не закончился, так что я должен позаботиться об этом:

IMG_0674.JPG

Yes, I hang deer in my workshop. I don't have a better place at the moment, but it works fine for now. Besides, despite how it may appear, I actually have plenty of room to skin and quarter the deer. By the time you read this post, the deer will be fully butchered, but with a week left in the season, I may yet shoot another.
Да, я повесюсь оленей в своей мастерской. В данный момент у меня нет лучшего места, но пока оно отлично работает. Кроме того, несмотря на то, как это может показаться, у меня на самом деле достаточно места, чтобы освежевать и четвертовать оленя. К тому времени, когда вы прочтете этот пост, олень будет полностью забит, но, поскольку до конца сезона осталась неделя, я ещё могу стрелить другого.

IMG_0677.JPG

Some time next week, I'll start repairing the gear, and I'll also have some more models to share. Who likes trains?
Как-нибудь на следующей неделе я начну ремонтировать шестерню, и у меня также будет ещё несколько моделей, которыми я могу поделиться. Кто любит поезда?
Sort:  

untitled.gif

Is there any reason not to just order a better-made gear from a supplier? They're basically industrial LEGO. If you know the specs, you can drop in a new one and maybe have better internals for the future to boot. Your repair is probably cheaper, though, since you have the tools.

I'll look into finding a replacement from a gear manufacturer only if my repair effort doesn't work. As it is, I thought about simply ordering a replacement gearbox, but I've already beaten my head against a wall trying to find replacement parts.

The cutter, BTW, was $111, including shipping. Assuming that I don't need to replace the hoses on my torch (seeing as I haven't used it for a few years), that's the total cost of this job. The replacement gear would probably be cheaper. Too bad it isn't plastic, I'd just print one... but then I'd probably have to do that every time I use the damn saw.

Can you tell whetehr those gears were originally hobbed or formed by sintering?

You should check out the AvE Youtube channel if you haven't already. A crazy Canadian talks shop, and sometimes tears down power tools to see whether they're skookum as frig or a piece of shit.

Definitely sintered gears.